squaredtree.blogg.se

15 September 2022 - 16:23
Pi datalink 2013 install kit
Allmänt
Pi datalink 2013 install kit









  1. #Pi datalink 2013 install kit driver#
  2. #Pi datalink 2013 install kit full#
  3. #Pi datalink 2013 install kit software#
  4. #Pi datalink 2013 install kit free#
  5. #Pi datalink 2013 install kit mac#

The shield itself is powered by a programmable XMC 32-bit ARM® MCU with embedded Brightness Color Control Unit (BCCU, XMC1200 MCU series), for flicker-free LED dimming and color control. The RGB LED Lighting Shield with XMC1202 uses a DC/DC buck topology and is able to drive up to 3 LED channels with constant current. It is designed to be easily configurable and combinable for different LED light engines and lamps, for fast prototyping and in-expensive evaluation of LED lighting applications. The RGB LED lighting shield from Infineon technologies is one of the first intelligent evaluation boards compatible with Arduino as well as Infineon’s XMC1100 BOOT KIT. RGB LED Lighting Shield with XMC1202 Hardware Compatible with Arduino 2 x 40-pin connectors with I/O signals RM 2.54mm 10-pin header for DAP (Debug Access Port) RJ45 Ehernet connector (if Ethernet supported by device)

pi datalink 2013 install kit

MicroUSB connector for ASC0 interface and debug Multi Voltage Safety Micro Processor Supply TLF35584 Ethernet PHY (if Ethernet is supported by device) On board microUSB debug/flash connector

Real-Time Clock with alarm, SRAM and unique Mac ID LCD XGA Display 320 x240mini SD card slot write, compiler and debug your first program

Link to the Free TriCore Entry Tool Chain including Getting Started, first 3 steps to

3 x 32-bit scalar TriCore CPU running at up to 300 MHz in the full automotive temperature range

To simplify the development of your own application, the kit is supplied with a variety of on-board components including a highly integrated software development environment that gives you everything you need to compile, debug, and flash your AURIX multi-core application. Low-cost and flexible application development platform for the 32-bit AURIX multi-core TriCore family. Connector for external board or RF-EEPROM.MCU current ammeter with 4 ranges and auto calibration.Digital Microphone MEMS Accelerometer and magnetometer Mems.Four directions Joystick with selection.LCD 24 segments, 4 commons in DIP 28 package.Three different interfaces supported on USB:.STM32L476VGT6 microcontroller featuring 1 Mbyte of Flash memory, 128 Kbytes of RAM in LQFP100 package.Supported by a wide choice of integrated development environments.Comprehensive free software including a variety of examples, part of STM32Cube package.Power supply output for external applications: 3.3 V or 5 V.Ethernet connector compliant with IEEE-802.3-2002.4.3-inch 480x272 color LCD-TFT with capacitive touch screen.USB functions: virtual COM port, mass storage, debug port.On-board ST-LINK/V2-1 supporting USB re-enumeration capability.STM32F746NGH6 microcontroller featuring 1 Mbytes of Flash memory and 340 Kbytes of RAM, in BGA216 package.Comprehensive free software including a variety of examples, part of STM32CubeF4 package or STSW-STM32136 for legacy Standard Libraries usage.Extension header for LQFP100 I/Os for a quick connection to the prototyping board and an easy probing.Two USB OTG LEDs: LD7 (green) VBus and LD8 (red) over-current.Four user LEDs: LD3 (orange), LD4 (green), LD5 (red) and LD6 (blue).

CS43L22, audio DAC with integrated class D speaker driver.

pi datalink 2013 install kit

  • MP45DT02: ST MEMS audio sensor, omnidirectional digital microphone.
  • LSM303DLHC: ST MEMS system-in-package featuring a 3D digital linear acceleration sensor and a 3D digital magnetic sensor.

    • pi datalink 2013 install kit

  • 元GD20: ST MEMS motion sensor 3-axis digital output gyroscope.
  • External application power supply: 3 V and 5 V.
  • Board power supply: through USB bus or from an external 5 V supply voltage.
  • On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone ST-LINK/V2 (with SWD connector for programming and debugging).
  • STM32F411VET6 microcontroller featuring 512 KB of Flash memory, 128 KB of RAM in an LQFP100 package.
  • Comprehensive free software including a variety of examples, part of STM32CubeF3 package or STSW-STM32148 for legacy Standard Library usage.
  • Extension header for LQFP48 I/Os for a quick connection to the prototyping board and easy probing.
  • Four user LEDs: LD3 (red), LD4 (orange), LD5 (green) and LD6 (blue).
  • High brightness LED dimming with buck converter.
  • External application power supply: 3 V and 5 V.
  • Board power supply: through USB bus or from an external 5 V supply voltage.
  • USB ST-LINK with re-enumeration capability and three different interfaces:.
  • On-board ST-LINK/V2-1 with selection mode switch to use the kit as a standalone ST-LINK/V2-1 (with SWD connector for programming and debugging).
  • STM32F334C8T6 microcontroller featuring 64 KB of Flash memory, 16 KB RAM in an LQFP48 package.











    • Pi datalink 2013 install kit
    0 kommentar(er)
    Om Mig: